Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Installation Cost in Yonkers?
Gate installation in Yonkers, NY typically runs between $1,800 and $7,500 for most residential projects in 2026, with the average homeowner spending around $3,400. A basic single-swing aluminum driveway gate with a manual latch starts near the low end, while a custom steel sliding gate with an electric opener, intercom, and keypad access climbs toward $9,000 or more. The final number depends on gate material, driveway width, whether you’re adding automation, and how much site prep your existing fence line needs.
You won’t find a meaningful “average” by googling around, because every Yonkers property is different. A gate for a driveway off Central Park Avenue has different site constraints than one on a hill off McLean Avenue. We’ll break down exactly where the money goes so you can price your project intelligently before you call anyone.
Key Takeaways on Yonkers Gate Installation Pricing
- Basic residential gate installation (manual, aluminum, single swing): $1,800 – $3,200
- Mid-range gate with electric opener and one keypad: $3,500 – $5,500
- Custom steel or wrought-iron gate with full automation: $6,000 – $9,500+
- Gate opener installation alone (existing gate): $850 – $1,900 including the opener unit
- Most Yonkers installations finish in 1 – 2 days for a standard residential driveway gate
- Calder Gate Repair Yonkers gives you a written price before any work starts. The number on the invoice is the number you agreed to at the door.
Gate Installation Cost Breakdown (2026)
Here’s a line-item look at what a typical Yonkers gate installation costs. These are real market ranges based on what we quote and install across the city’s neighborhoods, from Dunwoodie to Crestwood to Bryn Mawr Park.
| Line Item | Typical Range (Yonkers, 2026) | Notes |
|---|---|---|
| Basic aluminum single-swing gate (up to 10 ft) | $900 – $1,800 | Powder-coated, standard latch |
| Steel or iron single-swing gate | $1,600 – $3,200 | Heavier construction, better for wide driveways |
| Double-swing (bi-fold) gate set | $2,500 – $5,500 | Two panels, center latch |
| Sliding gate (single cantilever or track) | $3,000 – $6,500 | Best for sloped or tight driveways; common in hilly Yonkers sections |
| Gate opener unit (LiftMaster, FAAC, BFT, Linear) | $500 – $1,100 | Unit only, before labor |
| Opener installation labor | $350 – $800 | Includes wiring, limit setup, safety sensors |
| Keypad or intercom access system | $250 – $900 | Wireless keypad at the low end; video intercom at the high end |
| Site prep (leveling, concrete footing, post setting) | $400 – $1,500 | Yonkers’ rocky soil can push this higher |
| Removal and haul-away of old gate | $150 – $450 | Disposal included |
These ranges reflect what homeowners across Yonkers are actually paying this year. A straightforward install on a relatively flat driveway in Northeast Yonkers lands toward the lower end. A double-swing iron gate on a sloped driveway off Tuckahoe Road with an opener, two keypads, and a video intercom pushes into the upper brackets.
What Affects Gate Installation Pricing in Yonkers
Six things move the needle more than anything else. Here’s what actually changes your quote.
- Gate material. Aluminum is the most affordable and holds up well to Yonkers’ freeze-thaw winters without rusting. Steel and wrought iron cost 40 – 70% more but offer greater strength for wide spans and a more substantial look. Wood gates, while charming, need ongoing sealing against Hudson Valley humidity and are priced between aluminum and steel for custom work.
- Driveway width and slope. A single 8-foot gate is the cheapest option. Double gates spanning 16 – 20 feet require two panels, a center latch, and often a heavier opener, pushing costs up. Sloped driveways, common in the hilly sections between Riverdale and McLean Avenue, usually call for a sliding gate instead of a swing gate, which adds $1,000 – $2,500 to the project.
- Automation vs. manual. Adding an electric opener, whether it’s a LiftMaster or a BFT, adds $850 – $1,900 to the total when labor and unit are combined. Most Yonkers homeowners opt for automation, and for good reason: nobody wants to step out of the car in February slush to hand-swing a gate.
- Access control features. A basic remote is usually included with the opener. Wireless keypads run $250 – $450 installed. Video intercoms that connect to your phone run $600 – $900 installed. If you want a license plate reader or integration with a smart home system, expect to add $500 – $1,200.
- Existing fence and pillar condition. If you have brick pillars or stone columns, the gate needs to hang from them safely. Cracked or shifting pillars require reinforcement first, which can add $300 – $800. If you’re installing fresh posts, concrete footings in Yonkers’ compact glacial soil sometimes require deeper excavation, adding $200 – $500.
- Permit requirements. The City of Yonkers requires a building permit for gate installations that include new footings or electrical work, which applies to most automated gates. Permit fees are typically $100 – $300. A licensed installer handles this paperwork for you, and you should never skip it: unpermitted electrical work on a gate opener becomes a problem if you ever sell the home.
Gate Opener Installation: What It Costs on Its Own
Already have a gate but want to automate it? A standalone gate opener installation in Yonkers runs $850 – $1,900, including the opener unit and labor. The spread depends on the brand and drive type.
Entry-level openers like the Mighty Mule MM371W or Ghost Controls TDS2 run $500 – $700 for the unit. Mid-range and heavy-duty openers from LiftMaster, FAAC, or BFT, which handle higher traffic and wider gate spans, run $800 – $1,100. Linear and Viking models fall in between. Calder Gate Repair Yonkers is factory-familiar with nine major opener brands, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so you’re not stuck if you have an unusual setup from a prior owner.
Labor for opener installation typically runs 4 – 6 hours, and that includes proper arm alignment, limit switch adjustment (the small sensor that tells the gate when to stop at the fully open or closed position), and safety sensor installation. Skipping the safety sensors to save money is a mistake. They prevent the gate from closing on a car, child, or pet, and they’re required by code on any automated gate in New York.
How to Save on Gate Installation
Nobody wants to overpay, and there are legitimate ways to keep the total down without buying something you’ll be replacing in four years.
- Get the sizing right the first time. A gate that’s too wide for your driveway wastes material money. A gate that’s too narrow means your SUV clips the post every time. Have the site measured before you commit. Calder does this as part of every free estimate.
- Choose aluminum for non-security applications. If you just need a visual boundary and a way to keep the dog in the yard, a powder-coated aluminum single gate will last decades in Yonkers weather and costs half what iron runs.
- Buy the opener and gate as a package. Purchasing the gate panel and opener from the same installer as one project saves you $200 – $500 compared to two separate visits.
- Plan for the permit upfront. It costs more to retroactively permit work than to file it correctly the first time. A legitimate installer includes the permit line item in the written quote, not as a surprise add-on later.
- Ask about the 365-Day Done Right Promise. We include free return visits for one year on every installation if something isn’t right. That’s not a $99 extended-warranty upsell. It’s standard, it’s on paper, and it means you don’t pay a second service charge if a limit switch drifts or an arm comes out of alignment.
For an exact number on your specific driveway, call (585) 496-2148. The estimate is free, it’s in writing, and it comes with a live arrival time you can track before the technician shows up.
Is Gate Installation Worth It in Yonkers?
If you’re on the fence about spending $3,000 – $5,000 on a gate, here’s the honest way to think about it in this market. Yonkers homes with driveway gates sell on average for 4 – 7% more than comparable homes without them, according to local real estate comps through late 2025. A gate signals a secured perimeter, which matters on busier streets like Yonkers Avenue, McLean Avenue, and the side streets feeding into Saw Mill River Road.
Beyond resale, there’s the daily quality-of-life factor. If you have young kids, a gate is a boundary that doesn’t require you to be outside supervising. If you park late at night, an automated gate means you’re not walking to the edge of a dark driveway to open a manual leaf. And if you’ve had any package theft or unwanted car turnarounds on your street, a closed gate removes your driveway from the equation.
The cheapest alternative, a manual chain-link gate, runs $800 – $1,400 installed. It’s functional. It’s also rust-prone, loud, and not much of a visual improvement. Most people who go that route end up replacing it with a proper gate within three years, which means they pay twice. Our Gate Installation in Yonkers page goes deeper into the different gate styles that work well on Yonkers properties.
How Gate Installation Works, Step by Step
Here’s the process from first call to final walkthrough, so you know exactly what to expect. On a standard residential gate install, timeline is 1 – 2 days.
- On-site measurement and quote (30 – 60 minutes). A technician visits your property, measures the driveway opening, checks post/pillar condition, evaluates slope and soil, and discusses your access control preferences. You receive a written quote before anyone leaves the driveway.
- Permit filing (1 – 3 business days, handled by us). If your install includes new footings or electrical work, Calder pulls the Yonkers building permit. This is included in the quote, not billed separately after the fact.
- Site prep and footing work (half day). Posts are set in concrete, or existing pillars are reinforced. If the old gate is present, it’s removed and hauled away. Wiring for the opener is run at this stage.
- Gate and opener installation (half day to full day). The gate panel is hung, adjusted for level and swing/slide clearance, and the opener is mounted. Limit switches are set so the gate stops precisely at fully open and fully closed positions. Safety sensors are installed and tested.
- Access control setup (same visit). Remotes, wireless keypads, and any intercom or smart-home integrations are programmed and tested. We walk you through each device before we leave.
- Final walkthrough and written guarantee. We test the full cycle: open, close, obstruction detection, auto-reverse. You receive a digital invoice you can pay from a link, plus your written 365-Day Done Right Promise guarantee.
This is the Relay Standard we hold ourselves to: a live arrival time you can track, before-and-after photos, and a digital paper trail from booking to invoice. No vague four-hour windows. No phone tag.
Safety Notes on Automatic Gates
Automatic gates are heavier than they look. A sliding steel gate can weigh 400 – 800 pounds, and the opener exerts significant force. If the gate was installed incorrectly, that force becomes dangerous: pinch points at the hinge, or a gate that doesn’t auto-reverse when something’s in the way. The Consumer Product Safety Commission has documented serious injuries and fatalities from improperly installed or poorly maintained gate openers.
This is not a weekend DIY project. Proper installation requires setting limit switches accurately, calibrating obstruction sensitivity, mounting photo eyes at the correct height, and grounding the electrical correctly. If you have an existing gate opener that’s behaving erratically, don’t try to adjust the force settings yourself. Call a trained pro. Calder Gate Repair Yonkers covers gate repair, opener service, and full installations, all with the same written-pricing standard.
Choosing a Gate Installer in Yonkers: What to Ask
Not every fence company in Westchester does gates well. Here’s what separates a gate specialist from a general contractor who’ll “figure it out.”
- Ask how many opener brands they work with. If the answer is “whatever Home Depot carries,” you’re talking to a generalist. A gate specialist should be able to service and install LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule without blinking. That’s the full range of what you’re likely to encounter on a Yonkers property, and Calder is factory-familiar with all nine.
- Ask if the price changes after the work starts. The right answer is “no, it’s in writing before we begin.” If they hedge on that question, move on.
- Ask what happens if the gate fails in six months. If they tell you there’s a standard one-year parts warranty only, that’s decent. If they hand you a written guarantee with free return visits, that’s better. Calder’s 365-Day Done Right Promise puts it on paper: if the repair or installation isn’t right within 365 days, we come back at no charge.
- Ask who answers the phone at 9 PM when your gate won’t close. On the night your gate opens halfway and stays there, you want a live person, not a voicemail. Calder has a live person answering calls 24 hours a day, 7 days a week. No phone tree.
- Ask if technicians are background-checked. You’re inviting someone onto your property, often when you’re not home. The answer should be an immediate yes. All Calder technicians are background-checked and arrive in uniform.
Common Gate Types and What They Cost in Yonkers
Most Yonkers driveways fit one of three gate types. Here’s what each costs and where it makes sense.
Single Swing Gate: $1,800 – $3,200 (Manual), $2,800 – $5,200 (Automated)
A single panel hinged on one side, swinging inward or outward. Best for driveways 8 – 12 feet wide with enough flat space for the gate to swing without hitting a slope or a car parked too close. Aluminum is the most popular material at this size. Installation takes a day.
Double Swing Gate (Bi-Fold): $2,500 – $5,500 (Manual), $3,800 – $7,500 (Automated)
Two panels meeting in the middle. Good for driveways 12 – 20 feet wide. Requires two hinges per side, a center stop post or latch, and for automation, an opener wired to both panels or a single opener with a bi-fold arm kit. This is the most common style for larger Yonkers lots in Crestwood and Lawrence Park.
Sliding Gate: $3,000 – $6,500 (Manual), $4,200 – $8,500 (Automated)
One panel that slides horizontally along a track or cantilever system. The right choice for sloped driveways where a swing gate would drag, or for narrow frontage where there’s no room for the gate to swing. Sliding gates require more site prep and a longer bed than swing gates, which is why they cost more. Common on the steeper streets running east from the Saw Mill River Parkway.
What About Gate Repair vs. Gate Replacement?
At some point, a repair stops making financial sense and replacement becomes the smarter move. Here’s how to think about it.
If your gate is less than 10 years old and the problem is mechanical (opener, hinge, wheel, limit switch), repair nearly always wins. Most gate opener repairs in Yonkers run $180 – $420 before parts, and repairing a hinge or wheel runs $120 – $350. A repair costs a fraction of even a basic new gate.
If your gate is 15+ years old and you’re looking at multiple issues, rust through key structural points, or a failed opener that’s no longer manufactured, replacement usually wins. You could patch it up for $1,000 this year, then another $800 next year, and you still have an old gate. At that point, a new aluminum gate with a fresh opener and a full 365-Day guarantee is the better financial play.
The honest answer, which we’ll give you during a free estimate, depends on what we find. The gate’s age, material condition, and the cost of the specific repair all factor in. We’ll show you the math either way and let you decide.
FAQs – Gate Installation Cost
How much does a basic gate installation cost in Yonkers?
A basic manual aluminum single-swing gate costs $1,800 – $3,200 installed in Yonkers, including the gate panel, posts, hinges, and labor. If you want an electric opener added, figure $2,800 – $5,200 total. For an exact quote on your driveway, call (585) 496-2148 for a free estimate.
How much does an electric gate opener cost to install in Yonkers?
Gate opener installation runs $850 – $1,900 including the opener unit and labor in Yonkers. Entry-level units like Mighty Mule and Ghost Controls sit at the lower end; heavy-duty LiftMaster, FAAC, and BFT openers run higher. Calder is factory-familiar with all nine major opener brands, so we’ll recommend the right unit for your gate’s weight and cycle frequency.
Is it cheaper to repair or replace a gate?
If your gate is under 10 years old and the issue is the opener, hinges, or wheels, repair is almost always cheaper at $120 – $420 before parts. If the gate is 15+ years old with structural rust or multiple failing components, replacement at $1,800 – $5,000 typically beats repeated repairs. We’ll walk you through the numbers on both options during a free estimate, so you’re not guessing.
How long does gate installation take in Yonkers?
Most standard residential gate installations in Yonkers take 1 – 2 days from site prep to final programming. A basic single-swing gate on an existing concrete footing can finish in one day. A double-swing or sliding gate with new footings and automation typically takes two. You’ll get a specific timeline in your written quote before any work starts.
Do I need a permit for gate installation in Yonkers?
Yes, if your gate installation includes new concrete footings or any electrical work (which applies to all automated openers), a Yonkers building permit is required. Permit fees typically run $100 – $300. Calder includes permit filing in every written quote where it applies, so there’s no surprise at the end.
Can you install a gate opener on my existing gate?
Yes, in most cases. If your existing gate is structurally sound, we can retro-fit an opener in 4 – 6 hours, with total cost running $850 – $1,900 including the unit. The gate’s weight, width, and current hinge condition determine which opener we recommend. Call (585) 496-2148 and we’ll assess it in person, free of charge.
Get Your Yonkers Gate Installation Quote
If you’re ready to move forward, or just want to know what your specific driveway will cost, call Calder Gate Repair Yonkers at (585) 496-2148. You’ll reach a live person, day or night, and we’ll schedule a free on-site estimate with a background-checked technician who arrives at a time you can track.
Every quote is in writing before any work starts. Every job carries the 365-Day Done Right Promise: if the installation isn’t right within 365 days, we return at no charge. And the price on your invoice is the price you agreed to at the door, never a surprise. That’s how we do it, and that’s how it should be.
Pricing reflects the Yonkers market as of 2026. Calder Gate Repair Yonkers offers free estimates – call (585) 496-2148.
Written by Nico Alvarez, Owner at Calder Gate Repair Yonkers, part of the Relay Home Co. family serving Yonkers since 2009.
What Our Customers Say
"Solid work. ETA slipped by fifteen minutes, but I got a text."
- Holly B."Keypad and remotes reprogrammed in one visit. Paid by link."
- Pauline C."Slide gate wheels replaced. Glides smoothly now."
- Mark T.