Linear Keypad & Intercom Repair Nationwide

Linear Keypad & Intercom Repair: The Yonkers Owner’s Guide

Linear keypad and intercom repair in Yonkers typically runs $180 – $390 installed, and we stock the most common Linear-compatible keypads on the truck for same-day replacement. Most homeowners discover the failure the same way: the keypad stops accepting the code, the intercom goes quiet, or the gate only opens from the inside button. Sometimes it’s a corroded ribbon cable, sometimes the keypad membrane has worn through, and sometimes the circuit board has finally given up after a decade of Hudson Valley humidity. We fix all of it.

Call (585) 496-2148

We’re Calder Gate Repair Yonkers, the gate repair specialist inside the Relay Home Co. family. We’re an independent service provider, not affiliated with Linear or Nortek, but we’ve worked on enough Linear hardware across Westchester to know exactly which parts fail, which last, and what a repair should cost before we touch a single wire.

Key takeaways:

• Linear keypad and intercom repair in Yonkers: $180 – $390 installed, parts included
• We stock Linear-compatible keypads and intercom modules on the truck for same-day swaps
• Most failures are the keypad membrane, wiring at the hinge, or water intrusion in the enclosure
• Written price before any work starts, 365-Day Done Right Promise on every repair
• Call a live person 24/7 at (585) 496-2148

Which Linear Models This Applies To

The parts we replace most often in Yonkers come from the Linear MegaCode and Multi-Code series. You’ll find the model number printed on a sticker inside the keypad or intercom housing, usually starting with “AK” for keypads (AK-11, AK-21, AK-31) or “AM” for intercom modules (AM-KP, AM-3, AM-DKP). If the sticker’s faded or gone, we can usually identify it by the keypad’s button layout and wire count, but the sticker saves everyone time.

Here’s the compatibility gotcha that trips up a lot of Yonkers homeowners: Linear keypads from the MegaCode era use a specific frequency, 318 MHz, and older Multi-Code units run at 300 MHz. They are not interchangeable. Buying a cheaper aftermarket keypad on a different frequency means the receiver on your gate operator will ignore it entirely. We carry both frequencies in well-made aftermarket replacements that match the original specs, and when a customer wants OEM, we order genuine Linear parts with a 1-2 day turnaround. Either way, the written price covers the part and the install, so you know the difference in cost before you commit.

Signs Your Linear Keypad & Intercom Repair Is Failing

• Code works sometimes, not always. This is usually the keypad membrane wearing thin or the conductive traces inside cracking from years of weather exposure. In Yonkers, the freeze-thaw cycle every winter accelerates this. The fix is a new keypad assembly, not a new code.
• Gate opens from the house button but not the keypad. That isolates the problem to the keypad itself or its wiring. Sometimes it’s a broken conductor in the flex conduit near the gate hinge. A continuity test takes five minutes to confirm.
• Intercom is dead silent or hums. A constant hum points to a failing capacitor on the intercom board. Dead silence is often a wiring break at the hinge, or a power supply that’s drifted out of spec. We test the supply voltage before condemning the board.
• Keys have lost their click or press hard. The tactile dome switches under the keys wear out. You’re pushing harder, getting angry, and eventually the key doesn’t register at all. Replacement is the only real fix.
• Water or condensation inside the keypad lens. This is the beginning of the end for most Linear keypads. The weatherproofing gasket fails, moisture gets in, and the board corrodes. If you catch it early, we can sometimes clean and reseal it. If the board has green corrosion, it’s a swap.

Replacement Cost & What’s Included

In Yonkers, a Linear-compatible keypad replacement installed runs $180 – $260 for most single-family gate setups. Adding an intercom module or replacing both keypad and intercom together typically lands between $270 – $390. The range comes down to which model you have, whether we’re matching OEM or quality aftermarket, and how much of the existing wiring is salvageable.

Every quote includes the part, the labor, the programming of your existing codes, and testing the full cycle with the gate connected. You get a written price before any work starts, and the number on the invoice is the number we agreed to at the door. If the repair fails within 365 days, we come back at no charge. That’s the 365-Day Done Right Promise, and it’s in writing on every job, not mentioned as an afterthought.

DIY or Call Us?

A Linear keypad swap can look simple, and on a standalone pedestal with easy access, a confident homeowner can sometimes manage it. What we’d caution on: any wiring that runs through the gate hinge or underground. If the problem is the keypad and the wiring is sound, the job is a half-hour swap. If the wiring has been chewed by moisture or a poor splice is hiding in the junction box, you’ll spend a weekend chasing voltage and still end up on the phone.

The electrical side is low-voltage, but gate operators can store high voltage in their capacitors even with the power off. If you’re not sure which wire is safe to touch, don’t. Call us at (585) 496-2148 and we’ll walk through the symptoms with you on the phone. Nico Alvarez has been known to diagnose a Linear issue in under five minutes just by having someone describe what the keypad is doing. As he likes to say: “Tell me what the gate is doing wrong, I’ll tell you exactly what it needs and what it costs. No runaround.”

FAQs