Ghost Controls Gate Motor Replacement Nationwide

Ghost Controls Gate Motor Replacement: The Yonkers Owner’s Guide

We stock and install Ghost Controls-compatible gate motor replacements across Yonkers, with most jobs running between $450 and $900 installed depending on your model and swing or slide configuration. We keep the most common Ghost Controls motor assemblies on our trucks, so if you’re in Yonkers, call us before 2 p.m. and we can usually have your gate running the same day. Most owners discover the motor has failed when the gate starts moving slower than usual, stops halfway through a cycle, or simply goes silent after years of dependable service. A dead Ghost Controls motor isn’t subtle once it’s gone. The gate either groans and stalls, or it does nothing at all when you hit the remote.

Call (585) 496-2148

Which Ghost Controls Models This Applies To

Ghost Controls has shipped several distinct motor lines over the years, and the replacement motor that fits one series won’t always bolt onto another. The compatibility gotcha most Yonkers owners hit is this: Ghost Controls changed their actuator arm design between the original TDS series and the current AXT series, and the mounting geometry is not interchangeable without an adapter bracket. If your gate has a TDS motor (common on gates installed before 2016), you’ll need either a refurbished TDS motor or a full AXT retrofit kit. We can tell which one you have by the label on the side of the motor housing, and we’ll walk you through finding it over the phone in about two minutes. For most Ghost Controls swing gates, OEM motors run between $300 and $550 for the part alone. Quality aftermarket equivalents exist, but we’re cautious with them on Ghost Controls systems because the board communication protocol is picky about voltage curves. Our general rule: if your Ghost Controls system still has its original control board, we recommend OEM or factory-refurbished motors. If the board has already been replaced with a universal unit, a well-built aftermarket motor will work fine and save you $80 to $150.

Signs Your Ghost Controls Gate Motor Replacement Is Failing

• Gate moves slower than it used to, especially in cold weather. Yonkers winters are rough on the internal gear grease. When it thickens up and the motor has to work harder, slowdown is usually the first warning sign before total failure.
• Intermittent operation; sometimes it opens, sometimes it doesn’t. This often points to worn motor brushes. Ghost Controls motors are brushed DC units, and brushes are a consumable. Once they wear down, contact becomes inconsistent.
• Humming sound with no movement. The motor is getting power but the gears aren’t turning. Either the gear train is stripped or the capacitor is shot. This is a repair-or-replace call and not something to ignore.
• Gate stops mid-cycle and reverses or shuts down. The motor is overheating or the current sensor is tripping because the motor is drawing more amps than the board expects. This means the motor is laboring and on its way out.
• Remote works, everything clicks, but the gate stays put. That’s classic motor failure. The control board is fine and sending signal, but the motor itself can’t respond. If you’ve got that clicking sound, you’re likely looking at a replacement motor, and we can confirm in one visit.

Replacement Cost & What’s Included

In Yonkers, a Ghost Controls gate motor replacement with our team typically runs $450 to $900 installed. The spread comes down to three things: whether you have a single or dual gate, whether your system is TDS or AXT series, and whether we’re replacing just the motor or the motor plus the control board. A single swing gate motor replacement is on the lower end. A dual gate with both actuators and a board refresh lands on the higher end. Here’s the breakdown:

• Single swing gate motor replacement: $450 – $650 installed
• Dual swing gate motor replacement: $700 – $900 installed
• Motor plus control board replacement: $650 – $950 installed
• TDS to AXT retrofit (includes adapter brackets): $800 – $1,100 installed

Every price we quote includes the part, labor, testing, and a written guarantee on the work. We write the price before we touch a single bolt, and the number on your invoice is the number we agreed to at the door. If the motor or our work fails within 365 days, Calder Gate Repair returns at no charge to make it right. That’s our 365-Day Done Right Promise, and it’s in writing on every single job we do in Yonkers.

DIY or Call Us?

Here’s the honest split on Ghost Controls motor replacement. The electrical work on these systems is low voltage (typically 12 to 24V DC), so you’re not dealing with the same danger as a high-tension spring or a 120V line. But the mechanical side is where DIY attempts go sideways: the motor arm is under load from the gate’s weight, and if you unbolt the wrong side first, the gate can swing uncontrolled and hurt someone. We’ve also seen Yonkers homeowners strip the mounting threads by cross-threading bolts into the gate post during reassembly, which turns a simple motor swap into a post repair. If you want to check things yourself first, confirm the breaker is on, check for visible wire damage at the motor, and listen for that click we mentioned earlier. Those are safe checks. The actual replacement, alignment, and limit switch calibration are best left to a technician who does this daily. If you decide it’s not worth the risk, call us at (585) 496-2148 and we’ll get a real arrival time on the board.

Frequently Asked Questions