Ghost Controls Gate Repair Nationwide

Ghost Controls Gate Repair in Yonkers: What to Know First

Ghost Controls gate repair in Yonkers typically runs $180 – $340 for most opener and mechanical issues, and we can usually have a technician at your gate within one business day. As an independent Ghost Controls service provider, we repair every model line the company has made, including the TSS1, TDS2, and the newer Ghost Pro series, plus all Armor Alloy arm assemblies and keypads.

Call (585) 496-2148

This page is for Ghost Controls owners whose gate is acting up. You’ll find the failure modes we see most in Yonkers, what a repair actually costs, and what to expect when you call us at (585) 496-2148.

How Ghost Controls Products Fail – and How We Fix Them

Ghost Controls builds solid residential openers, but every brand has patterns. After years of servicing them across Yonkers, here’s what we see behind the service calls.

• TSS1 and TDS2 opener arms stripping the spindle gear. The arm that mounts to the gate post has a cast spindle connector that takes the brunt of a heavy gate. On older Yonkers properties, gates that have been swinging since the 80s are heavier than the opener was rated for, and that gear gives out. We replace the spindle assembly and set the travel limits so the arm isn’t fighting the gate’s full weight. This is the single most common Ghost Controls repair we do.
• Ghost Pro series limit switch drift. The limit switch is the small sensor that tells the gate when to stop. On Ghost Pro units, humidity and temperature swings near the Saw Mill River can cause the switch to lose its position, so the gate over-travels and slams or stops two feet short. We recalibrate the limits and seal the control housing properly so moisture stops getting in.
• Armor Alloy arm bending at the clevis pin. The clevis pin is the hinge point where the arm meets the gate bracket. If the gate ever got pushed manually while the opener was engaged, or if a wind gust caught it, that pin takes the damage. We see bent pins and wallowed-out clevis holes all the time in neighborhoods like Greystone and Dunwoodie. We straighten the arm, bore a fresh pin hole if needed, and install a new hardened pin.
• GhostControls keypad and wireless receiver losing pairing. The WKPREM keypad and the receiver inside the control box use a rolling code. After a power interruption, the two can fall out of sync and the keypad either blinks red or won’t execute commands. The fix is a factory re-pair, which takes about twenty minutes. If the keypad board is dead, we stock replacements and can swap it same-visit.
• Battery backup draining prematurely. The Ghost Pro series includes a battery backup that’s supposed to hold for several cycles. In Yonkers winters, cold-soaked batteries drop voltage faster, and the onboard charger sometimes doesn’t compensate. We test the battery under load, replace it if it’s below 70% of rated capacity, and verify the charging circuit is actually working. Many companies just swap the battery and move on. We make sure it’s not the charger killing it.

Our Ghost Controls Gate Repair Process

When you call, the first thing we do is have a live person on the phone. Not a menu tree. Nico or one of our senior techs will ask you what the gate is doing, or not doing. Half the Ghost Controls calls we get are diagnosed before a truck ever rolls.

1. 1
   Phone triage. You describe the symptom. We tell you the likely cause and a rough price range, so there’s no mystery.
2. 2
   Live arrival window. You get a trackable arrival time, not a vague four-hour block. Our tech shows up in uniform.
3. 3
   On-site diagnostic. We open the control box, test the board, battery, arm, limits, and safety sensors. We show you exactly what failed and explain it in plain words.
4. 4
   Parts decision. We discuss OEM Ghost Controls parts versus quality aftermarket options. OEM preserves your warranty position. In some cases, a good aftermarket part costs half as much and lasts just as long. You decide, with a written price before any work starts.
5. 5
   The repair and load test. We fix the issue, then run the gate through a full open-close cycle under load, checking the stops, force settings, and safety reverse.
6. 6
   Paperwork and the guarantee. You get a digital invoice you can pay from your phone, before-and-after photos, and our 365-Day Done Right Promise in writing. If it fails within a year, we return free.

What Ghost Controls Gate Repair Costs in Yonkers

Here’s the honest math on Ghost Controls repairs in Yonkers.

What moves the price is the gate’s weight, the age of the unit, and whether we’re repairing an existing opener or replacing a worn component entirely. Every job gets a written quote before we turn a single screw. Call (585) 496-2148 and Nico can usually give you a firm range on the phone in under five minutes.

Why Yonkers Homeowners Call Calder Gate Repair Yonkers for Ghost Controls Work

We’re a gate repair specialist inside the Relay Home Co. family, founded in 2009. That matters because Ghost Controls openers share a lot of DNA with other swing-arm brands we service daily, like LiftMaster, Mighty Mule, and DoorKing. If you ever migrate off the Ghost system, we’re already trained on what you’d move to. No handoff, no second contractor.

Every repair carries three fixed promises: a written price before work starts, a written guarantee on the repair, and a free second visit if it fails within 365 days. That’s our 365-Day Done Right Promise, and it’s not an add-on. It’s the standard. Our techs are background-checked, they wear uniforms, and they communicate like they’d want to be communicated with if it were their gate. Nico puts it this way: “Tell me what the gate is doing wrong – I’ll tell you exactly what it needs and what it costs. No runaround.”

FAQs