Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Motor & Opener Cost in Yonkers?
Gate motor and opener repair in Yonkers typically runs $195 to $540 for most mechanical or electrical fixes, while a full opener replacement including the motor, arm, and control board lands between $850 and $2,400 depending on the brand and gate size. Slide gate openers tend to run slightly higher than swing gate units because the rack and motor assembly is heavier. These are real Yonkers market numbers based on what we see at Calder Gate Repair week to week, not national averages that may not reflect what a tech in Westchester will actually quote you.
Gate Motor & Opener Cost Breakdown (2026)
Here is what you should expect to pay in Yonkers for the most common gate motor and opener services. These line items are what we write on invoices at Calder Gate Repair before any work begins, so the number you agree to is the number you pay.
| Service | Typical Cost in Yonkers | Notes |
|---|---|---|
| Diagnostic visit (waived with repair) | $49 – $89 | Applied toward the repair if you proceed |
| Limit switch replacement | $140 – $225 | Most common swing gate failure we see in Yonkers |
| Control board replacement | $280 – $520 | Higher for LiftMaster and Viking boards with built-in receivers |
| Capacitor replacement | $120 – $190 | Frequent on older FAAC and BFT swing motors |
| Gate opener arm replacement | $310 – $560 | Parts and labor; hydraulic arms cost more |
| Photo eye / safety sensor replacement | $110 – $185 | Per pair, including alignment |
| Gear set replacement (swing opener) | $265 – $480 | Includes regreasing the gearbox |
| Slide gate chain or belt replacement | $310 – $590 | Depends on track length; most Yonkers driveways run 16 – 25 ft |
| Full opener replacement (swing, single gate) | $850 – $1,800 | Mighty Mule and Ghost Controls at the low end; LiftMaster and Viking at the high end |
| Full opener replacement (slide gate) | $1,150 – $2,400 | Rack, motor, chain or belt, and controls |
What drives the number up? Gate weight is the big one. A solid wrought-iron gate on a Park Hill home weighs far more than an aluminum tube gate near McLean Avenue and needs a bigger motor. Brand matters too: a LiftMaster capacitor isn’t the same price as an off-brand equivalent, and we won’t install parts we wouldn’t trust on our own gates. Finally, access matters. If the gate post boxes are rusted or the previous installer buried the wiring without conduit, expect an honest conversation about additional labor before anything is signed.
What Affects Gate Motor & Opener Pricing in Yonkers
- Gate type and weight. Slide gates are heavier by design. A steel slide gate at a home off Central Park Avenue will strain a small motor within a few years, and you’ll pay for a beefier opener up front or repairs down the line.
- Opener brand. We service nine major brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Part prices vary sharply. A Viking control board can run $380 before labor; a Mighty Mule board is usually under $180.
- Age of the system. Yonkers has a lot of homes with 20-plus-year-old openers. Once a unit hits that age, hard-to-find capacitors and discontinued boards push repair costs toward half the price of new equipment, which is a data point worth knowing before you commit.
- Frozen or damaged mounting posts. We regularly see gates in the Lawrence Park area where the post wasn’t set below the frost line. The post heaves, the opener arm binds, and the motor burns out faster than it should. A new motor is one cost; resetting a post is another.
- Wiring and access conditions. Older Yonkers installations often have direct-burial wire without conduit. If the wiring has gone bad, tracing and replacing it adds $150 – $400 depending on the run length and whether we’re digging under concrete or stone.
- Overhead or confined entries. Some Bronx River Road and Glenwood Avenue properties have steep or tight approaches. If we need extra hands or special gear for the install, that shows up as a modest labor adjustment, but you’ll know about it in the written price first.
Common Gate Opener Problems and What They Cost to Fix
Most Yonkers calls start with a gate that won’t open, won’t close, or starts reversing midway. Here’s what we find and what it usually costs to correct.
Gate Won’t Open or Won’t Close
When a gate refuses to move at all, the top three culprits are a failed capacitor ($120 – $190 installed), a dead control board ($280 – $520), or a broken limit switch, the small sensor that tells the gate when to stop. On LiftMaster and BFT units, the capacitor is the usual first failure after years of daily cycling. On Viking and DoorKing slide openers, we see control board failures more often.
Gate Opens Then Immediately Reverses
This is almost always a photo eye or safety sensor problem. Dirt, misalignment, or a broken wire can trigger it. A set of replacement photo eyes runs $110 – $185 installed, including alignment. Sometimes it’s a force-setting issue on the motor, which is a $75 – $120 service call fix.
Gate Moves Partway and Stops
On swing arms, this points to a failing gear set or a cracked internal gear. A gear set replacement runs $265 – $480. On slide gates, a worn chain link or a stretched belt is usually the cause, and that’s $310 – $590 depending on track length. In Yonkers we see both patterns, but the slide-gate chain stretch is especially common on longer rural-style lots near the Saw Mill River corridor.
Motor Runs But Gate Doesn’t Move
That sound usually means the coupling between the motor and the gearbox has sheared, or the gear set has stripped. Fixing the coupling is $130 – $210. If the gears are gone, you’re looking at the $265 – $480 range. It’s worth noting that continuing to run a motor with stripped gears can overheat the motor itself and double the repair bill, so call when you first hear the grind.
Remote or Keypad Stopped Working
Before you buy new remotes, check whether the opener’s receiver board is the issue. A replacement remote for LiftMaster or Mighty Mule runs $40 – $85 programmed and synced. A full keypad with wiring is $110 – $170. If the receiver on the control board has failed, the board itself will need replacing at $280 – $520, and we’ll tell you that clearly before ordering parts.
Gate Motor & Opener Replacement Cost in Yonkers
When a repair bill approaches 60 percent of a new unit’s cost, we’ll tell you straight. On a 12-year-old FAAC swing opener with a dead board and a worn arm, that line gets crossed fast. Replacement is the better call, and here’s what the Yonkers numbers look like.
A single swing gate opener replacement runs $850 – $1,800 installed. Entry-level Mighty Mule and Ghost Controls units are on the lower end. A LiftMaster or Viking system with a battery backup and a stronger motor lands higher. For a dual swing gate, plan on $1,300 – $2,800.
Slide gate openers start at $1,150 for a light chain-drive unit and reach $2,400 for a belt-drive with a rack replacement and wireless capability. Most Yonkers slide gate installs fall between $1,400 and $1,900.
Every replacement we quote includes the labor to remove the old unit, mount the new one, rewire the low-voltage controls, program all remotes, and test the full open-close cycle at least a dozen times. You get a written price before we start, which is the only way Calder Gate Repair works.
How to Save on Gate Motor & Opener Repair
Gate openers are not flashy. The best way to save money is simple: fix small failures before they become motor replacements. That limit switch we mentioned costs $140 – $225. A burned-out motor because the switch was ignored costs three times that. Here’s how to keep the total down.
- Address grinding noises within a week. A $130 coupling is a cheap fix. Waiting until the gears strip pushes the bill over $400.
- Test your photo eyes seasonally. Wipe the lenses, especially after winter salt spray, and a $0 cleaning prevents a $185 sensor replacement.
- Keep the track clean on slide gates. Yonkers driveways collect grit, oak leaves, and ice melt. Debris on the track forces the motor to work harder and shortens chain and belt life.
- Don’t force a frozen gate. If the gate is stuck in winter, don’t hold the remote button down. The motor will burn out. Call us instead, the fix is usually faster and cheaper than a new motor.
- Get a written estimate. Calder Gate Repair gives you a written price before any work begins. The estimate is free, and it means you’ll never be surprised by the invoice. Call (585) 496-2148 to get one.
FAQs – Gate Motor & Opener Cost in Yonkers
How much does it cost to fix a gate opener in Yonkers?
Most gate opener repairs in Yonkers run $195 to $540 for common mechanical and electrical failures like limit switches, capacitors, couplings, and control boards. A full opener replacement ranges from $850 to $2,400. Call (585) 496-2148 for an exact quote, the estimate is free.
Is it cheaper to repair or replace a gate opener?
If the repair cost is under 60 percent of the price of a new unit and the opener is less than 10 years old, repair is usually the smarter money. A $190 capacitor on a 6-year-old FAAC makes sense. A $520 control board on a 15-year-old Viking slide opener starts tipping toward replacement. We’ll give you the numbers for both options before you decide.
How much is a LiftMaster gate opener replacement in Yonkers?
A LiftMaster swing gate opener replacement in Yonkers typically costs $1,000 to $1,800 installed, depending on gate weight and whether you need a battery backup. LiftMaster slide gate units run higher, usually $1,500 to $2,400. We install and program LiftMaster openers regularly and keep common components on the truck.
Can you repair a gate opener the same day?
In most cases, yes. Calder Gate Repair stocks common parts for LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so a single visit often covers the repair. If a special-order part is required, we’ll tell you the real arrival date before you pay anything. Call (585) 496-2148 and a live person answers, 24/7.
Why is my gate opener motor running but the gate won’t move?
That usually means the coupling between the motor and gearbox has sheared or the gear set has stripped. A coupling replacement runs $130 to $210 in Yonkers; a full gear set is $265 to $480. If you keep running the motor while the gate is bound, you can burn out the motor itself and triple the repair cost.
Do you charge a trip fee for gate opener estimates in Yonkers?
Estimates are free. We charge a $49 – $89 diagnostic fee only if we come out and you decide not to proceed with a repair, and we’ll tell you the fee before we book the visit. If you approve the work, the diagnostic fee is waived entirely. Call (585) 496-2148 to schedule.
Calder Gate Repair: Gate Motor & Opener Specialists in Yonkers
We’re not a general handyman service that occasionally touches a gate. Calder Gate Repair is the dedicated gate repair specialist inside the home services family, and we work on nine major opener brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. If you own a gate opener in Yonkers, odds are good we know the exact unit and the exact failure pattern before we even arrive.
Every job carries three non-negotiable guarantees. First, a written price before any work starts, the number on the invoice is the number you agreed to at the door. Second, a written guarantee on every repair. Third, the 365-Day Done Right Promise: if the repair fails within 365 days, Calder returns at no charge. That’s a free second visit, not a prorated discount.
Nico Alvarez leads the Calder Gate Repair Yonkers team. The technicians who show up are background-checked, uniformed, and dispatched with a live, trackable arrival time through The Relay Standard, so you’ll know exactly who is coming and when they will pull up to your driveway off Nepperhan Avenue or up the hill near Dunwoodie. You’ll get before-and-after photos of the work and a digital invoice you can pay from your phone, the way modern service should work.
We answer the phone 24/7. A live person, not a voicemail, not a chat bot. If your gate is stuck open at 2 a.m. and you want it closed for the night, someone picks up. For a free estimate on gate motor or opener work in Yonkers, call (585) 496-2148. The full Gate Motor & Opener service details for Yonkers are online if you want to read more first.
Pricing reflects the Yonkers market as of 2026. Calder Gate Repair Yonkers offers free estimates – call (585) 496-2148.
Written by Nico Alvarez, Owner at Calder Gate Repair Yonkers, serving Yonkers since 2009.
What Our Customers Say
"Keypad and remotes reprogrammed in one visit. Paid by link."
- Pauline C."Slide gate wheels replaced. Glides smoothly now."
- Mark T."Quote came in the app before the visit. No surprise at the end."
- Ginny L.